designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print 7.80 (ref) .307 12.55 .494 (ref) 16.49 .649 (ref) 3.94 .155 (ref) 1.27 (ref) .050 1.02 (ref) .040 5.08 (ref) .200 see note 2 sma-p-p-x-st-th1 shown fig. 1 8.00 .315 hex (ref) "a" "a" 3.05 0.20 .120 .008 2.28 - 0.10 0.00 .090 - .004 + .000 to center contact 0.92 (ref) .036 'b' 'c' section "a"-"a" coupling nut (sma-cnut-001) insulator (sma-ins-010) pin (sma-p-p-x-st-th1-pin) gasket (sma-gkt-001) c ring (sma-rng-001) body (sma-p-p-x-st-th1-bdy) 1/4-36 uns-2b (ref) 5.08 .200 5.08 .200 1.60 .063 (typ) recommended pcb layout 7.00 .276 (ref) 0.05 0.05 .002 .002 to insulator detail 'b' scale 8 : 1 0.15 .006 (typ 4 plcs) detail 'c' scale 8 : 1 b b -st: straight orientation -th1: through hole termination -h: gold (see notes 7 & 8) (SMA-P-P-H-ST-TH1-pin) (sma-p-p-f-st-th1-bdy) (sma-ins-010) (sma-cnut-001) (sma-rng-001) (sma-gkt-001) plating specification -p: pcb type -p: plug gender sma-p-p-x-st-th1 b b sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: sma straight, through hole plug- 50 ohm by: sma-p-p-x-st-th1 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 02/19/2008 1 1 sheet scale: 4:1 f:\dwg\misc\mktg\sma-p-p-x-st-th1-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 see table 1 notes: 1. represents a critical dimension. 2. stake around circumference 4 indents equally spaced. 3. pushout force for insulator: 44.48 n[10 lb] min. 4. center contact pushout force : 26.69 n [6 lb] min. 5. parts to be packaged in trays; if quantity is less than half tray, parts to be packaged in cohesive foam 6. rohs compliant. 7. component plating designations: -h: 0.000030" min. gold over 0.000050" min. nickel. -f: 0.000003" min. gold over 0.000050" min. nickel. 8. assembly plating designations: -h: (center contact)-h (outer contact)-f shell, body contact: brass gasket: silicon dielectric: ptfe ring: stainless steel revision a
|
